Rota-cone vacuum dryer

Rota-cone vacuum dryer
Product Description

Paul o abbe offers wide range of equipments which includes rota-cone vacuum dryer. It belongs to vacuum drying category. It is one of the most energy efficient, gentle and cost effective methods for drying solids to very low moisture levels. Because of the reduced vaporization temperatures possible under vacuum. It is ideal for drying heat-sensitive products pharmaceuticals, it is also ideal for developing the deep vacuum and temperatures necessary for solid-state polymerization of polyethylene terephthalate (pet) and polybutylene terephthalate (pbt). It offer many benefits including: predictable and repeatable results, dry temperature sensitive products, reduced energy, safe for friable products, more complete discharge, low cross contamination, easily cleaned, easily inspected interior, single enclosed environment, avoid oxidation. Contact us for more information.

Paul O. Abbe

  • US
  • 2017
    On CPhI since
Contract Service
Specifications
  • Selling Points
    Product Features; Prompt Delivery; Quality Service
  • Supplied from
    United States

Paul O. Abbe

  • US
  • 2017
    On CPhI since
Contract Service

More Products from Paul O. Abbe

  • Steel ball mills

    Product Steel ball mills

    Paul o abbe offers wide range of equipments which includes steel ball mills. It belongs to size reduction category. Benefits of tumble milling: high efficiency – due to the relatively slow rotational speed but large mass of media, more of the energy goes into milling and less wasted as heat. Narrow particle distribution – solids milled in tumble mills are normally so fine and consistent in size that it’s rare to require classification. Repeatable results – mill operating parameters including rotational speed, media size and milling duration can be independently controlled with known effect on the final results. Low temperature – because of the high efficiency of milling and low heat generation, the solids will not be exposed to high temperatures. For extremely heat sensitive products, cooling jackets can be provided on the mill cylinder. Chemical containment –solids are sealed and contained inside the mill, protecting the environment and operators. Predictable scale up – scale up from small to large mills is very predictable. Ball milling is one of the few unit operations that actual improve in performance and efficiency with increasing size. The abbe slice mill is the same as the product mill and can replicate all mill operating parameters but with very little product. Contact us for more information.
  • Ceramic lined ball mills

    Product Ceramic lined ball mills

    Paul o abbe offers wide range of equipments which includes ceramic lined ball mills. It belongs to size reduction category. Benefits of tumble milling: high efficiency – due to the relatively slow rotational speed but large mass of media, more of the energy goes into milling and less wasted as heat. Narrow particle distribution – solids milled in tumble mills are normally so fine and consistent in size that it’s rare to require classification. Repeatable results – mill operating parameters including rotational speed, media size and milling duration can be independently controlled with known effect on the final results. Low temperature – because of the high efficiency of milling and low heat generation, the solids will not be exposed to high temperatures. For extremely heat sensitive products, cooling jackets can be provided on the mill cylinder. Chemical containment –solids are sealed and contained inside the mill, protecting the environment and operators. Predictable scale up – scale up from small to large mills is very predictable. Ball milling is one of the few unit operations that actual improve in performance and efficiency with increasing size. The abbe slice mill is the same as the product mill and can replicate all mill operating parameters but with very little product. Contact us for more information.
  • Slice mill

    Product Slice mill

    Paul o abbe offers wide range of equipments which includes slice mill. It belongs to size reduction category. It is identical to the ball mills and ceramic lined mills in diameter and design the only difference is that they are as little as 12 in length. Since mill diameter dictates performance and mill length only affects capacity, it is used to develop or test formulations with little concern for scale-up factors. It is available to replicate any size ball or ceramic lined mill. It has custom designed around old or new mill in order to replicate the diameter, speed, cooling and wet or dry discharge. It can be designed for wet or dry milling including discharge housing. Contact us for more information.
  • One piece ceramic mill

    Product One piece ceramic mill

    Paul o abbe offers wide range of equipments which includes one piece ceramic mill. It belongs to size reduction category. These mills are made from a single monolithic alumina-ceramic casting with no seams to trap product or contaminants. These mills are ideal for smaller, high-quality batches of product requiring the highest purity milling environment. Contact us for more information.
  • Pivoting jar mills

    Product Pivoting jar mills

    Paul o abbe offers wide range of equipments which includes pivoting jar mills. It belongs to size reduction category. It is an another option of rotating any type of ceramic or steel jar is to have one or more jars held in a pivoting frame that rotates on trunnions mounted on bearings. This design allows the vertical loading and unloading of jars without having to lift a heavy jar on and off rollers. Separation grates can be provides to separate the milled product from the grinding media. Contact us for more information.
  • Jar rolling mills

    Product Jar rolling mills

    Paul o abbe offers wide range of equipments which includes jar rolling mills. It belongs to size reduction category. It is designed to support and rotate steel and ceramic jars individually or several at a time. The smallest bench top model, can handle 1 or 2 jars. The largest jar roller can have as many as four levels or tiers and from two to five rolls per tier. They are heavy duty, high load, and precision machines designed to operate reliably 24/7. Every roll is made of cast polyurethane that is machined for concentricity and smooth jar spinning. Each roll is supported by industrial pillow block roller bearing and the frames are heavy steel coated with industrial epoxy or powder coating. Contact us for more information.
  • Milling jars

    Product Milling jars

    Paul o abbe offers wide range of equipments which includes milling jars. It belongs to size reduction category. It is small scale version of the ball mills and are typically used in the laboratory or small scale production.it is rotated with the aid of a jar rolling mill, which has two rollers to support and rotate the jars at the proper speed. It is half filled with grinding media or balls from ¼” to 1” and as the mill rotates the solids are trapped between the ball and are milled down to as little as 1 micron by the cascading and tumbling action of the ball charge. Contact us for more information.
  • Rota-cone blenders

    Product Rota-cone blenders

    Paul o abbe offers wide range of equipments which includes rota-cone blenders. It belongs to mixing & blending category. It offers the lowest shear method of mixing friable or delicate solids. The simple double-cone or v-designs provide complete discharge. Because there is no agitator there are no seals and they are easily inspected and cleaned. For these reasons, tumble blenders are often employed by the pharmaceuticals industries. But because they do not have an agitator they can be used to blend dense materials including ceramics and powdered metals as heavy as tungsten carbide. Contact us for more information.
  • Rota-vee blenders

    Product Rota-vee blenders

    Paul o abbe offers wide range of equipments which includes rota-vee blenders. It belongs to mixing & blending category. It provide a low shear method of mixing friable or delicate solids. The simple v shape design provides complete discharge. Tumble blenders are often used in the food and pharmaceuticals industries. Contact us for more information.
  • Dual shaft ribbon and paddle mixers

    Product Dual shaft ribbon and paddle mixers

    Paul o abbe offers wide range of equipments which includes dual shaft ribbon and paddle mixers. It belongs to mixing & blending category. Contact us for more information.
  • Double arm mixers

    Product Double arm mixers

    Paul o abbe offers wide range of equipments which includes double arm mixers. It belongs to mixing & blending category. It is used for mixing plastics, rubber, adhesives, mastics up to 10,000,000 centipoise and solids such as carbon paste, powdered metals and ceramics. Double arm mxiers can be jacketed and vacuum rated for drying. Mixer discharge is tilt or bottom dump valves. Our mixer/extruder models utilize an independent screw to discharge solids. Contact us for more information.
  • Double arm mixer extruders

    Product Double arm mixer extruders

    Paul o abbe offers wide range of equipments which includes double arm mixer extruders. It belongs to mixing & blending category. It is used on plastics, rubber, adhesives, mastics up to 10,000,000 centipoise and solids such as carbon paste, powdered metals and ceramics. Double arm mxiers can be jacketed and vacuum rated for drying. Discharge is extrusion screw. Contact us for more information.

Recommended products